Sub Zero. Sunbrite Tv. Waste King. Wood Stone. Xo Ventilation. Items identified as Quick Ship will ship within 2 business days from our warehouse in Babylon, New York. Actual delivery times will vary based on your location.
If you are ordering multiple items and not all items qualify for Quick Ship, the order will ship when all items are available to ship. Quick Ship may not apply to multiple quantities of the same product. Subscribe to our mailing list. This item is discontinued but we may have a similar model. No Sales Tax. Avoid the headaches of out-of warranty repairs! Get the ultimate in home protection for your appliance!
Overall Width:. Overall Height:. Overall Depth:. Cutout Height:. Approximate Shipping Weight:. Flush-to-Cabinet Design:. Electronic Touch-Through-Glass Controls:. Retractable Master Control Dial:. Genuine European Convection:. Fast Preheat Bake Mode:. Fast Preheat Convection Bake:. Automatic Temperature Probe:. Convection Bake, Broil, Roast:. Standard Bake and Broil:. Coffeemaker Manuals. Computer Accessories Manuals. Computer Hardware Manuals.
Computer Keyboard Manuals. Computer Monitor Manuals. Convection Oven Manuals. Cooktop Manuals. Cookware Manuals. Cordless Drill Manuals. CRT Television Manuals. Digital Camera Manuals. Dishwasher Manuals. DJ Equipment Manuals. Door Manuals. Double Oven Manuals. DVD Player Manuals. DVR Manuals. Electric Cookie Press Manuals. Remove the 2 T20 screws on either side of the element terminals. Pull the element toward you so that the terminal wires are inside the oven cavity.
Disconnect the wires from the inner broil element terminals. Remove the 2 T20 screws securing the element to the broil reflector. Page 13 of 36 Service Manual for Bosch Built-in Wall Ovens The user interface control board is assembled onto a chassis and the entire assembly is serviced as a single unit.
Remove 2 T20 bolts from each side. Grasp one corner of the interface panel and lift upward, then pull it toward you see Figure Repeat on the other side. Disconnect the 3-wire yellow harness leading to PC control module.
To remove the user interface board and chassis from the manifold bracket, remove the 10 binding-head T20 screws securing the interface chassis to the bracket these screws are unique to the interface — notice the serrated underside. If the user interface assembly was difficult to remove, break the metal tabs off n to make it easier to reinstall; use pliers to bend the tabs back and forth until they break off. See Figure Figure 14 PC Control Module is visible after removing access panel.
Whenever possible, conduct troubleshooting tests at the control module. Refer to Figures 15 for plug and relay locations. Disconnect all wires. Remove 1 T20 screw securing control module to chassis. Slide module to the left to release the 3 tabs on the bottom of Page 17 of 36 Service Manual for Bosch Built-in Wall Ovens the module bracket from the 3 slots in the chassis. Always reset the oven and test after changing the control module.
In some cases, a second reset may be necessary. The motor is accessible from the rear, after removing the rear outer sheet metal panel. Disconnect the 2 wires from the motor terminals. Remove 3 T20 screws from the arms of the motor assembly.
Use a tap and a hammer to dislodge the assembly from the clips that secure it to the rear of the unit. Position tap on the arm secured by the rightmost clip. Triac switches VAC to the transformer. There are 4 terminals on the new transformer, as shown in Figure To clear a path for removing the bake element, it is necessary to remove the vertical air channel s and disconnect wires. Before proceeding, note the position of the wires. Pull wires out of plastic purse locks attached to upper and lower vertical air channels.
Remove upper air channel 4 T20 screws. Remove the screw between the element terminals. Tuck insulation up into the oven wall as necessary. While holding element terminals, lift element upward to clear the outer edge of the compartment. Hold element on both sides and lift upward as you slide it straight out. Remove 3 T20 screws securing the fan to the mounting bracket.
Remove 3 T20 screws securing the bracket to the oven housing. Slide bracket up and out to release it from the 2 tabs holding it in position. Reinstalling the Bake Element There are 2 tabs inside the element cavity, and the front tab will prevent the element from going in all the way. Use a ruler or the vertical air channel after removing plastic purse locks as a tool to guide the element back in. Place the tool inside the cavity, on top of the tab, then insert the element on top of the tool and slide it in.
After the element is beyond the front tab, remove the tool. Complete the installation. Replace the plastic purse locks clips if they were removed from the vertical air channel. Find it on the underside of the upper plenum access panel as shown in Figure There is tape around the motor windings and the terminals are labeled N, H, and L for reference, as shown in Figure The error codes which begin with E2 apply to the lower cavity of double ovens.
Diagrams referenced in the table can also be found in the appropriate Service Guide. Set Option Code properly. Check connections of all communication lines and control module inputs. User interface not getting all information from control module at start-up. Check for loss of communication or disconnected wire somewhere in unit Check user interface assembly. Inspect touch PCB. Refer to Diagram 1. Ensure wire harness not touching motor or pinched.
Confirm plenum not touching fan end cap. Check Hall Effect Sensor connection. Check probe receptacle and harness. Door switch is in undefined state. Door latch is in an undefined state.
0コメント